• Fast Delivery
  • Expert Support
  • Low Trade Prices
  • Quality Products
Safelease-WM-1-scaledSafelease-WM-1-scaled

Adomast Safelease Environmentally Friendly Formwork Release Emulsion – 25 Litre

Brand: Adomast
Product Code: ADO-SFLS-25
In Stock

Adomast Safelease is an environmentally friendly and highly efficient release material for concrete formwork on site. Safelease is ready to use and suited to outdoor use on faced sealed plywood, steel moulds and other impervious formwork materials. This variant is supplied as a 25 litre unit.

£47.15 incl. VAT
£39.29 excl. VAT

Qty:

Adomast Safelease Environmentally Friendly Formwork Release Emulsion.

Safelease is an environmentally friendly and highly efficient release material for concrete formwork on site. Safelease is ready to use and suited to outdoor use on faced sealed plywood, steel moulds and other impervious formwork materials.

This variant is supplied as a 25 litre unit.

Advantages:

  • Recommended for high quality finishes
  • WRAS approved product
  • Low to no odour
  • Safe, environmentally friendly product.
  • NO VOC content
  • Low viscosity for easy application
  • Readily biodegradable
  • After water evaporation, film is resistant to water wash off
  • Forms may be stripped early when other factors permit.
  • Suitable for use with white, coloured or standard OPC concrete finishes.
  • Non-staining
  • Fully compatible with the subsequent application of silicone or similar surface treatments when used as recommended

Coverage:

A thin coating is recommended giving a coverage between 30 to 40m2 per litre depending upon surface porosity and texture. Protect from rain when still wet.

Application:

Apply thinly, by spray, brush or swab prior to each concrete pour. Application should be a minimum of 1 hour before pouring, for the excess water to evaporate off and the release film to be properly established. With first application to new formwork a second light coat may be required.

On vertical forms any excess material accumulating at the bottom of the form should be removed. On untreated timber surfaces additional coats may be required for first use.

Specifications
Application Apply thinly, by spray, brush or swab prior to each concrete pour. Application should be a minimum of 1 hour before pouring, for the excess water to evaporate off and the release film to be properly established. With first application to new formwork a second light coat may be required.

On vertical forms any excess material accumulating at the bottom of the form should be removed. On untreated timber surfaces additional coats may be required for first use

Coating A thin coating is recommended giving a coverage between 30 to 40m² per litre depending upon surface porosity and texture. Protect from rain when still wet
Storage SAFELEASE is a water based product and should be protected from frost. Containers must be kept sealed after use. The product may require mild agitation again before use if stored for more than 6 months
Shelf life In excess of 12 months in sealed containers, use within 2 months of opening. Roll or agitate prior to use
Specification Safelease mould release agent is manufactured by Adomast Manufacturing Ltd and shall be applied
strictly in accordance with the manufacturer’s instructions. For specific advice regarding any aspect of this product, please consult our Technical Department
Health and safety Prolonged physical contact should be avoided and personal and environmental hygiene encouraged in
common with the use or all chemical products. Where contact with skin occurs, the material should be removed with soap and water. If splashes affect eyes, they should be bathed immediately with clean water and if discomfort persists, medical attention should be sought

Please see our our Delivery policy page for full details of our delivery terms and conditions, including information on exclusions, geographical restrictions, third parties, and failed deliveries.

Delivery Timescales

We will endeavour to deliver all orders within 1-3 working days (subject to geographical restrictions). Please note, where delivery lead-times for individual orders may be subject to change, we will keep you informed directly by phone or email within 24 hours of your order being placed.

Deliveries will not be made on UK bank holidays, and in such cases will fall on the next working day.

Standard delivery hours are between 8am and 6pm, Monday to Friday. If you are not available to accept the delivery when it is attempted, then a failed delivery charge will be applied (see the Delivery page for full details).

Delivery Communications

We aim to dispatch and deliver all our products within their specified time frames. You will get notified by BaseTec via email when your products have been dispatched. This will include details of your order and the expected delivery time. BaseTec will contact you via email or phone if there are any delays in picking your order or after dispatch.

If any products are out of stock or unavailable at the time of ordering, the BaseTec team will contact you by phone or email to discuss your options.

Reviews

There are no reviews yet.

Be the first to review “Adomast Safelease Environmentally Friendly Formwork Release Emulsion – 25 Litre”
Shopping Basket
INC VAT EX VAT